Operating Conditions
l  2.0V~5.5V Vcc Voltage Range
l  -40 ~ +105 Temperature Range
l  ESD 6KV
l  EFT 4KV
l  28 PIN: SOP28 / TSSOP28
l  Super-high-speed 1T 8051 core
l  The instruction set compatible with 8051
l  The execution speed is about twice that of other 1T 8051
l  Double data pointers (DPTRs)
l  32K bytes Flash ROM

n  Divided into 64 sectors

n  512 bytes per sector

n  Can be rewritten 100,000 times

n  The data written-in has more than 100-year preservation life in the ambient temperature of 25℃

l  IAP (In Application Programming): The area allowed IAP operation in Flash can be set to 0K,1K,2K or 32K by Customer Option.
l  BootLoader: Built-in 1K bytes LDROM

n  Boot from APROM or LDROM can be selected through the CODE OPTION Settings item

l  Unique ID: 96 bit unique ID memory
l  SRAM:

n  Internal 256 bytes of in-chip direct access RAM

n  4 Kbytes of external RAM (XRAM)

n  16 bytes Indirect access RAM in the chip read and write PWM duty cycle SFR: 1040H~104FH 16 bytes in total

Flash Programming and Emulation
l   2-wire JTAG programming and emulation interface
Clock Source
l  Built-in high frequency 32MHz oscillator (HRC)

n  The system clock frequency (fsys) of the IC can be selected and set by the programmer as: 32/16/8/4MHz

n  Frequency Error:

u  Within ±1% @ -20 ~ 85

u  Within ±2% @ -40 ~ 105

n  The system clock can be automatically calibrated by 32.768kHz external crystal oscillator, after calibration HRC accuracy can be infinitely close to the accuracy of external 32.768kHz crystal oscillator.

l  Built-in low-frequency crystal oscillator circuit: 32.768k oscillator can be connected externally as a Base Timer clock source.
l  Built-in low-frequency 32.768kHz oscillator (LRC): used as the clock source for Base Timer and WDT.
Low-voltage Reset (LVR)
l   4 options of reset voltage: 4.3/3.7/ 2.9/1.9V, the default value can be selected by the Customer Option
Interrupts (INT)
l  Up to 16 interrupt sources including Timer0~Timer4, INT0~2, ADC, PWM, UART, USCI0~2, Base Timer, TK
l  External interrupt INT0~2 contains 3 interrupt vectors, 13 intermediate fractures. All can set up rising edge, falling edge, double edge interrupt.
l  Two-level interrupt priority capability
Digital Peripheral

n  Up to 26 bidirectional independently controllable I/O ports, independent setting of pull-up resistors

n  All I/Os have large sink current drive capability (50mA)

l  Built-in WDT, optional clock frequency division ratio
l  5 Timers: Timer0~4
l  8-channel 16-bit PWM

n  Can be set to independent mode or complementary mode: 8 channels of PWM in the independent mode, the duty cycle can be set separately

n  In complementary mode, four sets of complementary PWM waveforms with dead zones can be output simultaneously

n  The output waveform can be reversed and can be set to center-aligned or edge-aligned

n  Fault detection mechanism

l  One independent UART communication port UART0
l  Three UART/SPI/TWI communication interfaces (USCI)
l  Integrated with 16 * 16-bit hardware Multiplier-Divide Unit (MDU)
l  Built-in CRC check module
Analog Peripheral

l  23-channel dual-mode TouchKey (TK) circuit.

n  High-sensitivity mode applicable to TouchKey sensor, proximity induction and other TouchKey applications featuring high requirements on sensitivity

n  High reliability mode features very strong anti-interference which is able to pass 10V dynamic CS test

n  Support self-capacitance programme and reciprocal- capacitance mode.

n  Support  low power consumption mode.

n  Complete development support: High-flexible touch software library, intelligent software of debugging.

l  11-channel 12-bit high-speed ADC

n  1MHz sampling clock

n  The ADC reference voltages is optional:

u  Internal 2.048V

u  Internal 1.024V

u  VDD

n  One internal channel can measure the voltage of the power supply

Power Saving Mode
l  IDLE Mode: can be woken up by any interrupt
l  STOP Mode: can be woken up by INT0~2,  Base Timer and TK.


Select all
Title Describe Version Language Type Size Updated Download
datasheet V1.0 English PDF 2.12MB 2021-10-29 Download
Select all
Title Describe Version Language Type Size Updated Download
The key points of the MCU PCB design of SailOne touch button MCU are introduced V1.0 English PDF 1.62MB 2023-02-02 Download
Select all
Title Describe Version Language Type Size Updated Download
The key points of using the 95F series products are introduced V1.0 English PDF 566KB 2023-02-02 Download
The key points of using the 95F series TouchKey MCU products are introduced V1.0 English PDF 3.25MB 2023-02-02 Download
Select all
Title Describe Version Language Type Size Updated Download
selection guide V1.0 English PDF 4.47MB 2022-04-06 Download